I connected the network gateway to the serial port of my computer, started microcom and powered up the device. This is the output in the factory configuration untill the prompt:
U-Boot 1.1.4-at0 (Jan 3 2007 - 10:30:09) U-Boot code: 00000000 -> 000144f7 data: 24000000 -> 24002d80 SDRAM: 32 MB at address 0x10000000 Testing SDRAM...OK malloc: Using memory from 0x11fc0000 to 0x12000000 Flash: 8 MB at address 0x00000000 DRAM Configuration: Bank #0: 10000000 32 MB In: serial Out: serial Err: serial Net: macb0, macb1 Press SPACE to abort autoboot in 1 seconds ### JFFS2 loading 'uImage' to 0x10200000 Scanning JFFS2 FS: ....... done. ### JFFS2 load complete: 912671 bytes loaded to 0x10200000 ## Booting image at 10200000 ... Image Name: Linux-2.6.18-atngw Image Type: AVR32 Linux Kernel Image (gzip compressed) Data Size: 912607 Bytes = 891.2 kB Load Address: 10000000 Entry Point: 90000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel at 90000000 (params at 11fc0040)... pdc pdc.0: Atmel Peripheral DMA Controller enabled EIM: External Interrupt Module at 0xfff00000, IRQ 19 EIM: Handling 4 external IRQs, starting with IRQ 64 smc smc.0: Atmel Static Memory Controller at 0xfff03400 pio0: Atmel Port Multiplexer at 0xffe02800 (irq 13) pio0: Handling 32 external IRQs, starting with IRQ 96 pio1: Atmel Port Multiplexer at 0xffe02c00 (irq 14) pio1: Handling 32 external IRQs, starting with IRQ 128 pio2: Atmel Port Multiplexer at 0xffe03000 (irq 15) pio2: Handling 32 external IRQs, starting with IRQ 160 pio3: Atmel Port Multiplexer at 0xffe03400 (irq 16) pio3: Handling 32 external IRQs, starting with IRQ 192 pio4: Atmel Port Multiplexer at 0xffe03800 (irq 17) pio4: Handling 32 external IRQs, starting with IRQ 224 dmac0: DesignWare DMA controller at 0xff200000 irq 2 NET: Registered protocol family 2 IP route cache hash table entries: 256 (order: -2, 1024 bytes) TCP established hash table entries: 1024 (order: 0, 4096 bytes) TCP bind hash table entries: 512 (order: -1, 2048 bytes) TCP: Hash tables configured (established 1024 bind 512) TCP reno registered JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler cfq registered (default) Serial: Atmel USART3 driver usart.1: ttyS0 at MMIO 0xffe01000 (irq = 7) is a USART3 loop: loaded (max 8 devices) eth0: Atmel MACB at 0xfff01800 irq 25 (00:04:25:1c:75:fc) eth1: Atmel MACB at 0xfff01c00 irq 26 (00:04:25:1c:75:fd) physmap platform flash device: 00800000 at 00000000 physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0041 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cmdlinepart partition parsing not available RedBoot partition parsing not available Using physmap partition information Creating 3 MTD partitions on "physmap-flash.0": 0x00000000-0x00020000 : "u-boot" 0x00020000-0x007f0000 : "root" 0x007f0000-0x00800000 : "env" atmel_spi atmel_spi.0: Atmel SPI Controller at 0xffe00000 (irq 3) mtd_dataflash spi0.0: AT45DB642x (8448 KBytes) ip_conntrack version 2.4 (256 buckets, 2048 max) - 204 bytes per conntrack ip_tables: (C) 2000-2006 Netfilter Core Team TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Time: avr32 clocksource has been installed. VFS: Mounted root (jffs2 filesystem). Freeing init memory: 56K (90000000 - 9000e000) init started: BusyBox v1.4.2 (2007-04-17 15:34:55 CEST) multi-call binary * mounting virtual filesystems: /proc /sys /dev /dev/pts /config /tmp /var/run /var/lib/samba /var/log * set mdev hotplug ... [ OK ] * mdev ... [ OK ] * setting hostname ... 'ngw.example.net' * network loopback ... [ OK ] * starting syslogd ... [ OK ] * log messages to syslog ... [ OK ] * starting klogd ... [ OK ] * probing modules ... vfat loaded, mmc_block loaded, atmel-mci loaded, [ OK ] * mounting filesystems: /usr * setup eth0 ... [ STATIC ] (10.11.12.1) * setup eth1 ... [ OK ] * network ... [ OK ] * starting telnetd ... [ OK ] * enable ipv4 forwarding ... [ OK ] * iptables postrouting ... [ OK ] * iptables incoming trafic ... [ OK ] * iptables outgoung trafic ... [ OK ] * starting dnsmasq ... [ OK ] * running ntpdate ... [ FAILED ] * starting dropbear ... [ OK ] * starting inted ... [ OK ] * starting nmbd ... [ OK ] * starting smbd ... [ OK ] * starting winbindd ... [ OK ] * starting httpd ... [ OK ] * get board type for GPIO ... 'NGW' * setup GPIO boot LED ... [ OK ] * setup GPIO LED A ... [ OK ] * setup GPIO LED B ... [ OK ] Network Gateway ready BusyBox v1.4.2 (2007-04-17 15:34:55 CEST) Built-in shell (ash) Enter 'help' for a list of built-in commands. ~ #
Advertisement
